RX 300 Lexus + Lexus RX-300 Cars + Governing bodies and operation receptions + Settings and routine maintenance of the car + Engine + Systems of cooling of the engine, heating, ventilation and air conditioning + the Power supply system and production of the fulfilled gases + Systems of electric equipment of the engine + Automatic transmission and interaxal differential + Transmission line + Brake system + Suspension bracket and steering - Body - External equipment and body elements Removal and installation of the top strut of an impellent compartment Removal and installation of bumpers Removal and installation of a cowl, its lock and decorative reshyotka of a radiator Removal, installation, dismantling and assembly of a forward door and its components Removal, installation, dismantling and assembly of a back door and its components Removal, dismantling, assembly and installation of a door of a back and its components Removal and installation of cleaners and windscreen fairing Removal and installation of moldings Removal and spoiler installation Removal and installation of the top hatch + salon Equipment + Onboard electric equipment + Schematic diagrams of electric connections
|
Removal, dismantling, assembly and installation of a door of a back and its components
Components of a door of a back
|
- Insert a screw-driver between a door of a back the top panel of furnish of glass and wring out the panel from clamps on its perimeter.
- Separate the socket and remove from the top panel of furnish of glass a stoplight of the top level.
- Inserting a screw-driver between a door of a back and elements of furnish of a door, wring out consistently from clamps the top panel, both lateral and the bottom panel.
- Turn out a nut and remove the screen wiper lever.
- Turn out a nut and remove a washer э / the screen wiper motor from the outer side of a door.
- Separate the socket, turn out three bolts and remove э / the screen wiper motor.
- Separate sockets, turn out on 4 bolts and remove the back combined lamps with consolidations.
- Disconnect from the lock cylinder the socket, turn out two bolts and remove the cylinder.
- Turn out two bolts, remove the mechanism of management of the lock and disconnect from it a cable.
- Disconnect from the lock draft, give two nuts and remove the lock activator. Separate the socket.
- Separate the socket, turn out 4 bolts and remove the lock.
- Turn out two screws and remove rasseivatel of illumination of registration plate.
- Turn out two nuts and remove the external handle.
- Turn out a nut and wring out a screw-driver an external overlay of a door of a back from clamps.
- Remove the handle for door lifting.
- Give fixture of loops to a door and remove a door.
- At installation of the door which is especially new, it is necessary to adjust its situation.
- For door adjustment in the directions to the left/to the right and up/down give bolts of fastening of loops to a door, expose a door in demanded situation and tighten bolts with effort of 8 Nanometers.
- For door adjustment in the directions up/down and inside/outside give bolts of fastening of loops to a body, expose a door in demanded situation and tighten bolts with effort of 12 Nanometers. For a reversing of bolts at first:
- Remove a lens of the lamp of a luggage compartment;
- Turn out four bolts, separate the socket and remove the lamp;
- Wring out a screw-driver back section of furnish of a roof from clamps and remove it.
- If necessary adjust position of the drummer of the lock, moving it (tapping with a hammer) at the released fixture outside/inside and up/down. Previously remove the bottom panel of furnish проёма back doors. Upon termination of adjustment tighten bolts of fastening of the drummer with effort of 23 Nanometers and establish the panel.
- In summary adjust the provision of a lateral stopper.
- Installation is made upside-down. Tighten fixture with demanded efforts, use new clamps.
- In conclusion of installation adjust positions of the lever of a screen wiper (see. Section condition Check, adjustment and replacement of brushes of screen wipers).
|
- After installation check, that the top point of hit of a stream of washing liquid on glass was in the shaded area, and the bottom point – in a screen wiper scope.
|
|
|
|
|