RX 300 Lexus
+ Lexus RX-300 Cars
+ Governing bodies and operation receptions
+ Settings and routine maintenance of the car
+ Engine
+ Systems of cooling of the engine, heating, ventilation and air conditioning
+ the Power supply system and production of the fulfilled gases
+ Systems of electric equipment of the engine
+ Automatic transmission and interaxal differential
- Transmission line
General information
Removal and driveshaft installation
Removal, dismantling, assembly and installation of forward power shafts
Removal, dismantling, assembly and installation of back power shafts
Replacement of a forward epiploon of back differential
Replacement of lateral epiploons of back differential
Removal and installation of the case of back differential, differential dismantling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Schematic diagrams of electric connections
|
Removal, dismantling, assembly and installation of back power shafts
Removal and installation
Components of a back power shaft
|
|
- Remove the corresponding back wheel.
- Turn out two bolts and remove back section of an exhaust pipe together with laying.
- Turn out a bolt and remove the sensor of speed of ABS.
- Take a pin, remove fixing cap and turn out a stupichny nut.
- Put labels on the case of the tripodny hinge and on a flange of back differential.
- Turn out 4 nuts, remove washers and disconnect a power shaft from differential.
- Remove a power shaft from the holder.
- Installation is made upside-down. Tighten fixture with demanded efforts, after installation check serviceability of functioning of ABS sensors, and also check and if necessary adjust corners of installation of back wheels.
|
|
Dismantling
|
|
- Check power shafts:
- External hinges should not have excessively big люфта;
- Make sure of smoothness of movement of the internal hinge in the support direction;
- Make sure of absence excessively big люфта internal hinges in the radial direction;
- Check protective covers on existence of damages.
- By means of a screw-driver remove collars of protective covers of hinges.
|
|
- Put labels on the case of the tripodny hinge and on a power shaft and remove the hinge case from a power shaft.
|
|
|
Do not use for drawing of labels a chisel. |
|
|
- Remove a lock ring and put labels on the tripodny hinge and on a power shaft.
|
|
|
Do not use for drawing of labels a chisel. |
- Bring down a hammer and a pig from soft metal the tripodny hinge from a power shaft.
- Remove protective covers with collars.
- The external hinge is not subject to dismantling.
- Fix a power shaft in a vice with soft sponges and by means of a screw-driver and a hammer bring down from a shaft a boot No. 2, trying not to damage a rotor of the sensor of speed of ABS.
|
|
Do not damage a rotor of the sensor of speed of ABS. |
|
|
Assembly
|
|
|
|
- Napressuyte a new boot No. 2 on a shaft.
|
- Temporarily establish new covers of hinges with collars.
|
|
Before installation of protective covers wind shlitsa of a power shaft with a vinyl tape to prevent their damage. |
- Place on a power shaft the tripodny hinge a konusny part to the external hinge and level adjusting labels of the hinge.
- Napressuyte the hinge on a power shaft by means of a hammer and a pig from soft metal. Establish a lock ring.
- Fill in a cover of the internal hinge 180 ÷ 190 of g of yellow greasing, level adjusting labels of the case of the hinge and fix the case to differential.
- Fill in a cover of the external hinge 107 ÷ 117 of g of gray greasing.
|
|
- Make sure that covers come into grooves on driving to a shaft and are not deformed at standard length of a shaft.
|
- Fix protective covers collars, having tightened them a screw-driver.
|
|
|
|