LEXUS RX 300

1998 — 2003 of release

Repair and car operation


RX 300 Lexus
+ Lexus RX-300 Cars
+ Governing bodies and operation receptions
+ Settings and routine maintenance of the car
+ Engine
+ Systems of cooling of the engine, heating, ventilation and air conditioning
+ the Power supply system and production of the fulfilled gases
+ Systems of electric equipment of the engine
+ Automatic transmission and interaxal differential
+ Transmission line
+ Brake system
- Suspension bracket and steering
   General information
   + Forward suspension bracket
   + Back suspension bracket
   - Steering
      Checks of components of a steering
      Removal, installation, dismantling and assembly of a steering column
      Removal and installation of the pump GUR and its driving belt
      Removal, installation, dismantling and assembly of the steering mechanism
   + suspension bracket Geometry
+ Body
+ Onboard electric equipment
+ Schematic diagrams of electric connections



Removal, installation, dismantling and assembly of a steering column

Components of installation of a steering column

1 — the Overlay of a steering wheel
2 — the Steering wheel
3 — the Screw with a head under a prutkovy key
4 — the Bottom cap No. 3 of a steering wheel
5 — the Bottom cap No. 2 of a steering wheel
6 — Bottom taxiing up a plate of furnish of devices
7 — the Top section of a casing of a steering column
8 — the Block of podrulevy switches with a spiral spring

9 — Assembly of a steering column
10 — Assembly of the steering hinge
11 — the Bottom section of a casing of a steering column
12 — the Collar
13 — Assembly of No. of 2 consolidations of an opening for a steering column
14 — Assembly of an intermediate shaft
15 — Bottom taxiing up the panel of furnish of the dashboard
16 — the Bottom left lateral insert of furnish of the dashboard
17 — the Lever of unlocking of the lock of a cowl

Components of assembly of a steering column

1 — the Coil of a transponder of an immobilizator of the engine
2 — Assembly of illumination of the lock of ignition
3 — the Switch of the prevention of extraction of a key from the ignition lock
4 — Ø/m the valve of blocking of the ignition key
5 — the Cylinder of the lock of ignition
6 — the Amplifier of a transponder
7 — the ignition Switch
8 — the Top arm of a steering column
9 — the Arm of the switch of indexes of turns

10 — Dempfernaya a plate
11 — a damper Latch
12 — Directing a dempferny plate
13 — the Top holder of a steering column
14 — the Returnable spring of the lever of adjustment of an inclination of a steering column
15 — Bolts
16 — the Pipe of a steering column
17 — the Support of a pipe of a steering column
18 — the Bottom fastening of a pipe of a steering column

Removal and installation

 PERFORMANCE ORDER

  1. Establish wheels in the provision of rectilinear movement.
  1. Remove the bottom caps No. 1 and No. 2 of a steering wheel and turn out bolts with heads of odes a prutkovy key so that cuts in their heads entered into an emphasis.
  1. Remove from a steering wheel a slip, having separated the socket of electroconducting of a safety cushion. Lay a slip the face up.

At socket separation when finding the ignition key in the situation "ON" or "ACC" in the control unit the malfunction code registers.


Do not assort an overlay of a steering wheel.

  1. Separate the socket and turn out a nut of fastening of a steering wheel.
  2. Put adjusting labels on a steering wheel and on a steering shaft then remove a steering wheel.
  3. Verify two bolts, separate the socket, disconnect a cable of a drive of the lock of a cowl and remove the bottom podrulevy panel of furnish of the dashboard.
  4. Turn out two bolts and remove the bottom left lateral insert of furnish of the dashboard.
  5. Turn out three screws and remove the top and bottom casings of a steering column.
  6. Separate sockets of podrulevy switches, the safety cushion socket, turn out screws and remove assembly of podrulevy switches with spiralno spring.
  7. Remove a spiral spring.

Do not assort a spiral spring and do not allow oil hit on it.

  1. Weaken a collar of assembly of an intermediate shaft.
  1. Put adjusting labels on an intermediate shaft and a shaft of the steering mechanism, give «A» bolt, turn out a bolt of "B" and disconnect assembly of an intermediate shaft.
  1. Remove the bottom podrulevy plate of furnish of devices, separate the socket, turn out adjusting nuts of a steering column and remove it.
  2. Turn out a bolt of "A" and remove assembly of an intermediate shaft with assembly of No. of 2 consolidations of an opening for a steering column.
  3. Remove assembly of No. of 2 consolidations of an opening for a steering column from assembly of an intermediate shaft.
  4. Remove a collar.
  1. Put labels on the hinge and a shaft of a steering column.
  1. Turn out a bolt and remove assembly of the steering hinge.
  2. Installation is made upside-down. Combine the adjusting labels put at removal, tighten fixture with demanded efforts.

Dismantling and assembly

 PERFORMANCE ORDER

  1. Turn out the screw and remove the coil of an immobilizator and assembly of illumination of the lock of ignition.
  2. Remove the top arm and the top holder of a steering column, having drilled 2 bolts.
  3. Turn out two bolts and remove an arm of the switch of indexes of turns.
  4. Remove a returnable spring of the lever of adjustment of an inclination of a steering column.
  5. Turn out a bolt, remove a washer and remove a support of a pipe of a steering column with the bottom fastening of a pipe of a steering column.
  6. Disconnect the bottom fastening of a pipe from a support.
  7. Remove latches of dampers, dempferny plates and their directing.
  8. Assembly is made upside-down.