Новости В России | mercedes- mercedes- mercedes обслуживание цена в Воронеже

LEXUS RX 300

1998 — 2003 of release

Repair and car operation



RX 300 Lexus
+ Lexus RX-300 Cars
+ Governing bodies and operation receptions
+ Settings and routine maintenance of the car
+ Engine
+ Systems of cooling of the engine, heating, ventilation and air conditioning
+ the Power supply system and production of the fulfilled gases
+ Systems of electric equipment of the engine
+ Automatic transmission and interaxal differential
+ Transmission line
+ Brake system
- Suspension bracket and steering
   General information
   - Forward suspension bracket
      Removal, dismantling, assembly and installation of a nave and rotary fist
      Removal, dismantling assembly and installation of a rack of a suspension bracket
      Removal and installation of the bottom lever of a suspension bracket
      Check and replacement of a spherical support of a suspension bracket
      Removal, installation and check of the stabilizer of a suspension bracket
   + Back suspension bracket
   + Steering
   + suspension bracket Geometry
+ Body
+ Onboard electric equipment
+ Schematic diagrams of electric connections



Forward suspension bracket

Removal, dismantling, assembly and installation of a nave and rotary fist

Removal and installation

Components of installation and assembly of a nave and rotary fist

1 — the Rack of a forward suspension bracket
2 — the Tip of steering draft
3 — the Sensor of speed of ABS
4 — Assembly of a rotary fist and a wheel nave
5 — the Power shaft
6 — the Brake support
7 — the Brake disk
8 — Shplint
9 — the Fixing cap

10 — Stupichny a bolt
11 — Nizhny the suspension bracket lever
12 — the Boot
13 — the Bearing
14 — the Lock ring
15 — the Rotary fist
16 — the Protective casing
17 — a wheel Nave


 PERFORMANCE ORDER

  1. Remove a forward wheel.
  2. Measure axial люфт the bearing of a nave of a forward wheel and axial palpation of a nave. For this purpose previously remove a brake support and a brake disk (see. Head Brake system).

Reliably tie up a support so that it was not bent and the flexible brake hose was not loaded. Compare results of measurements to requirements of Specifications of Head the Suspension bracket and a steering and if necessary replace the nave bearing. Establish to the place of a brake disk and a support.

  1. Take шплинт lock-nuts of a power shaft and, having squeezed out a brake pedal, turn out a lock-nut.
  2. Remove a brake support and a brake disk (see. Head Brake system).

Reliably tie up a support so that it was not bent and the flexible brake hose was not loaded.

  1. Turn out fixture of the sensor of speed of ABS and the holder of his electroconducting.
  2. Weaken, two nuts of fastening are resistant suspension brackets to a rotary fist.

Bolts yet do not take.


  1. Take шплинт nuts of a tip of steering draft, turn out a nut and by means of the special adaptation disconnect a tip of steering draft from a rotary fist.
  1. Turn out a bolt and two nuts and disconnect a spherical support from the bottom lever of a forward suspension bracket.
  2. Completely turn out two bolts of fastening of a rack of a suspension bracket to a rotary fist and remove assembly of a rotary fist with a nave.

Do not damage a protective casing and a rotor of the sensor of speed of ABS.

  1. Installation is made upside-down. After installation check a signal from the ABS sensor.

Dismantling and assembly

 PERFORMANCE ORDER

  1. Take a screw-driver a boot.
  1. Take шплинт nuts of fastening of a spherical support, turn out a nut and by means of the special adaptation remove a spherical support from a rotary fist.
  1. Remove a nave by means of the special adaptation.
  1. Vypressuyte an internal holder (outside of) the nave bearing.
  2. Turn out 4 bolts and remove a protective casing of a rotary fist.
  3. Take a lock ring and выпрессуйте the nave bearing from a rotary fist.
  1. If necessary remove nave bolts by means of the special adaptation. Installation of bolts is made by a nut tightening.
  1. Assembly is made upside-down. Tighten connections with demanded efforts. At installation of a boot level an opening in it (for the ABS sensor) with an opening on a rotary fist. Use the new stupichny bearing and new шплинт nuts of fastening of a spherical support.