LEXUS RX 300

1998 — 2003 of release

Repair and car operation



RX 300 Lexus
+ Lexus RX-300 Cars
+ Governing bodies and operation receptions
- Settings and routine maintenance of the car
   General information
   General information about settings and adjustments
   Schedule of routine maintenance
   Check of levels of liquids, control of leaks
   Check of a condition of tires and pressure of their rating, rotation of wheels
   Replacement of impellent oil and oil filter
   General checks of brake system
   Check and replacement of the salonny filter of a heater and To/in
   Check of a condition and replacement of hoses of an impellent compartment, localization of leaks
   Check of a condition and replacement of belts of a drive of auxiliary units
   Replacement of a filtering element of an air purifier
   Check of a condition of system of production of the fulfilled gases
   Check and replacement of spark plugs
   Replacement of brake liquid, pumping of brake system
   Check of a condition of components of a suspension bracket and steering
   Check of a condition of protective covers of power shafts and driveshaft hinges
   Check of operability of lighting devices, horn and heater fan
   EVAP system check
   Condition check, adjustment and replacement of brushes of screen wipers
   Check of a condition of the battery and care of it
   Replacement of cooling liquid (OZh)
   Check and adjustment of klapanny gaps
   Check and adjustment of a course of pedals of the working and parking brake
   Check of boots of the parking brake
+ Engine
+ Systems of cooling of the engine, heating, ventilation and air conditioning
+ the Power supply system and production of the fulfilled gases
+ Systems of electric equipment of the engine
+ Automatic transmission and interaxal differential
+ Transmission line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Schematic diagrams of electric connections


Soap2day offers a seamless streaming experience for users worldwide.


Replacement of impellent oil and oil filter

Long contact of skin to the fulfilled impellent oil is quite dangerous. Use protective cream or put on rubber gloves during carrying out described below procedures.


Frequent replacement of impellent oil is the main preventive procedure of the service, to the available amateur mechanic. Eventually oil is subject to a razzhizheniye and pollution that conducts to premature wear of the engine.

Spuskaniye of impellent oil

Impellent oil can be pumped out by means of a probe through directing tube щупа.


 PERFORMANCE ORDER

  1. Warm up the engine to working temperature of cooling liquid.
  2. To Poddomkratta the car also establish it on props, or tire out on a viewing hole.
  3. Substitute under a drain stopper capacity in volume about 6 l for collecting the fulfilled oil.
  1. Turn out a drain stopper and let's to oil flow down completely.

Do not burn a hand the warmed-up following oil!

  1. Check a condition of the fulfilled oil. If in it there is at a large number a metal shaving and wear products, it indicates existence задиров, for example, in bearings of a cranked shaft and shatunny bearings. For an exception of damages after the carried-out repair it is necessary to clear carefully oil channels and hoses, and also, at the corresponding complete set, to replace a maslookhladitel.

Replacement of the oil filter

 PERFORMANCE ORDER

  1. Turn out the oil filter from a flange. For this purpose it is possible to use the special adaptation or a tape key. It is possible to insert also a sharp screw-driver sideways into the filter, thus oil therefore in advance substitute capacity for collecting oil under the filter will start to follow from the filter.
  1. Wipe a surface of the oil filter and its flange on the block of cylinders and remove sealing laying if it remained on a flange.
  2. Grease sealing laying of the new oil filter by pure impellent oil.
  3. Screw the new oil filter by hand. After laying will lie down to a flange on the block of cylinders, tighten the filter on three quarters of a turn. Pay attention to the remarks provided on the case of the filter.

Engine filling by oil

At replacement it is necessary to use oil of identical type and, whenever possible, identical brand. It is for this purpose recommended to fix at each replacement of oil on the engine a label with the indication of brand and viscosity of oil. Impellent oils of identical type and identical brands, but different viscosity can fill in during appropriate time of year.


 PERFORMANCE ORDER

  1. Screw a carving stopper of a drain opening with a new sealing ring and tighten it with effort of 45 Nanometers.
  2. Uncover a jellied mouth and fill in impellent oil approximately on half of liter less, than it is specified in Specifications (see. Section Check of levels of liquids, control of leaks).
  3. Start the engine and let's to it work idling, having checked meanwhile existence of leakages of impellent oil.
  4. Wait for 5 minutes, then check level of oil and if necessary modify it.
  5. Make a trial trip on the car and check a drain stopper and the oil filter on leaks. If necessary, carefully tighten them. Once again check oil level, if necessary modify it.